Taylors Doors manufactures Maxi Single Leaf Hinged Fire Resistant doors utilizing a vermiculite core (TVC40) which is stable and contains no asbestos or mineral fibers.
Maxi Fire Resistant doors are edged with an internal (nominal) 10mm solid timber edge rail to all four (4) sides with a selection of door facings dependent on the finish required and/or fire rating required.
Our standard range of door facings include;
- Paint Grade Ply (sheet thickness 3.6mm)
- Duracote Tempered Hardboard (sheet thickness 3.2mm)
- MDF (sheet thickness 4mm or 6mm where routed patterns are requested)
- If 6mm face sheeting is used this will require a larger frame rebate to accommodate the additional door thickness)
The core used in the manufacture of our Maxi Fire Resistant doors is 38.5mm thick.
Dependent on the facing required the finish thickness of the Maxi Fire Resistant door will vary.
The following table outlines the approximate finished door thickness for a Maxi Fire Resistant door based on the standard facing options.
| Door Type | Facing | Approximate Thickness (mm) |
|---|---|---|
| Maxi | Duracote | 44.9 |
| Paint Grade Ply | 45.7 | |
| MDF (4mm) | 46.5 | |
| MDF (6mm) | 50.5 |
The following table details the maximum door size based on standard wall types. If the wall type you are building into or fixing to is not listed, contact our office to confirm that an available test certificate is available for installing a TVC core fire resistant door into the specific wall type as required under AS1905.1.
The following table lists product limitations in accordance with AS1905.1-2005.
| Available Sizes in accordance with AS1905.1-2005 | |||
|---|---|---|---|
| For doorsets to be certified in accordance with AS1905.1-2005, frames must be back filled | |||
| Wall Type | Maximum Height x Width | Facing | Maximum FRL |
| Plasterboard | 2400 x 1200 | MDF | ---/60/30 |
| Ply | ---/120/30 | ||
| Duracote | |||
| Masonry | 2400 x 1200 | MDF | ---/60/30 |
| Ply | ---/120/30 | ||
| Duracote | ---/240/30 | ||
The following table lists product limitations in accordance with AS1905.1-1997.
| Available Sizes in accordance with AS1905.1-1997 | |||
|---|---|---|---|
| For doorsets to be certified in accordance with AS1905.1-1997, frames may not be required to be back filled. Contact us for backfill requirements under AS1905.1-1997. | |||
| Wall Type | Maximum Height x Width | Facing | Maximum FRL |
| Plasterboard | 2400 x 1200 | MDF | ---/60/30 |
| Ply | ---/120/30 | ||
| Duracote | |||
| Masonry | 3500 x 985 | MDF | ---/60/30 |
| 3050 x 1220 | |||
| 2700 x 1500 | |||
| 3500 x 985 | PLY | ---/120/30 | |
| 3050 x 1220 | |||
| 2700 x 1500 | |||
| 3500 x 985 | Duracote | ---/240/30 | |
| 3050 x 1220 | |||
| 2700 x 1500 | |||
The following optional extras are available for Maxi Fire Resistant doors;
- Vision panels
- Air Grilles
- Seal provisions (routed provision in the bottom of the door)
- Tunnel lock provisions (a drilled cable transfer hole through the width of the door leaf for electric locks)
- Custom route pattern facings (suitable for MDF faced doors only with MDF face sheet thickness increased from 4mm to 6mm giving an additional 4mm door thickness)
- Bollection moldings (customer to specify molding design as we do not carry a standard molding maximum molding size 20mm high x 40mm wide)
- External edge rails
- Special veneer facings
- Stainless steel kick plates
- Non combustible backing
- Steel sheet and capping (Zincanneal, Galvabond and Stainless Steel)